Umbrel or Start9 pool? Add a backup pool in AxeOS

By DirectPool. Published . Updated
Short answer

Keep your node's Public Pool as the primary pool and add DirectPool as the AxeOS fallback, if your firmware shows fallback fields: host stratum.directpool.io, port 3338 for solo or 3333 for PPLNS, your bc1 or 3 address as user, x as password. When the node is down, the miner keeps hashing.

Fallback solo
3338
Fallback PPLNS
3333
Password
x
Fee
1%

Why does a home node pool need a backup?

Umbrel and StartOS (Start9) can run Public Pool, an open source solo pool, next to your own Bitcoin node. Pointing a Bitaxe at it means your miner builds blocks from your own node. The catch is that the pool is only up when the node is: every app update, OS update, reboot, power cut or resync stops it. A miner with nowhere to send work just waits, and those hours are lost.

A backup (fallback) pool fixes that. The miner keeps hashing somewhere else while the node is down. It costs nothing when the node is up, because the fallback is only used when the primary cannot be reached.

Does your AxeOS have a fallback pool?

AxeOS (ESP-Miner) has had a fallback stratum pool for a long time: its API exposes fallbackStratumURL, fallbackStratumPort, fallbackStratumUser and fallbackStratumPassword, and reports isUsingFallbackStratum when the backup is active. The exact screen differs between versions, and development builds are moving to numbered pool slots. So check what your installed firmware shows before you rely on it:

  • Open the miner's IP address, then Settings (Pool on newer versions).
  • Look for a Fallback section, or a second pool slot. If neither exists, your firmware has no fallback and the settings below do not apply. Update AxeOS from the official release page first.
  • Field labels below are the common ones; your version may word them slightly differently.

What goes in the primary pool?

Your node's Public Pool. Open the Public Pool app on Umbrel or StartOS: it shows the stratum address and port to use on your local network. Copy them from there rather than guessing; they depend on your node's address and setup. The user is your Bitcoin address, plus an optional .workername.

Careful: Public Pool only produces valid work when the node is fully synced. During initial sync, point the miner at DirectPool as primary and switch later.

Which fallback settings do you enter?

1. Choose solo or PPLNS for the fallback

To keep the same all-or-nothing deal as your node pool, use DirectPool solo on port 3338: a block found there pays the whole reward to your address, minus 1%.

FieldWhat to enter for DirectPool
Fallback Stratum Hoststratum.directpool.io
Fallback Stratum Port3338
Fallback Stratum Userbc1qyouraddress.bedroom
Fallback Stratum Passwordx

If you would rather earn small, steady amounts while the node is down, use PPLNS on port 3333 instead, which can use your closest regional server:

FieldWhat to enter for DirectPool
Fallback Stratum Hoststratum.directpool.io
Fallback Stratum Port3333
Fallback Stratum Userbc1qyouraddress.bedroom
Fallback Stratum Passwordx
Choose your mining region
Showing Europe, Lithuania (main server).
Changing the location only changes the address shown above. Copy it into your miner settings and restart or reconnect the miner. Miners already connected stay where they are. Every server mines the same pool, with the same payouts.
Browser ping, measured live from this page
Europe, Lithuania...
North America, Chicago...
Asia, Jakarta...
This measures your browser connection, not your miner or the full relay-to-pool path.

2. Save and restart

Click Save, then Restart. The miner connects to the primary pool as usual.

3. Test it once

Stop the Public Pool app for a few minutes. The AxeOS dashboard should show the fallback pool as active, and your address should appear on the DirectPool solo page (port 3338) or the home page (port 3333). Start Public Pool again. Whether and when the miner returns to the primary on its own depends on the firmware version; the dashboard shows which pool is active, and a restart always starts from the primary.

Can you do it the other way round?

Yes. Many people keep DirectPool as the primary and their node as the fallback, or skip the node pool entirely. With DirectPool as primary, use the same values in the main Stratum fields and put your Public Pool address in the fallback fields. The rules for every DirectPool field are in stratum URL, worker and password explained.

How are fallback shares paid?

  • On Public Pool, your own node builds the block; a block found pays your address.
  • On DirectPool solo (3338), a block found pays your address from the block, minus 1%.
  • On DirectPool PPLNS (3333), each pool block pays every miner by their shares over 7 days, minus 1%, with a 10,000 sat minimum; smaller balances wait for a later block.

None of these holds a balance for you, and there is no account. Your chance of a block at your hashrate, per day and per year, is on the odds calculator.

What goes wrong most often?

  1. Using umbrel.local or another name the miner cannot resolve. If the miner will not connect to the node, use the node's IP address.
  2. Typing stratum+tcp:// in a host field. AxeOS host fields take the bare host.
  3. Different addresses in primary and fallback by accident. Copy and paste the same one.
  4. Never testing the fallback. Stop the node pool once and watch the switch.

More checks are in the connection checklist.

Q

Questions

Why add a backup pool to a Bitaxe that mines to my node?
Your node pool stops during updates, reboots, power cuts and resyncs. A fallback pool keeps the miner hashing until the node is back.
Does every AxeOS version have a fallback pool?
No. Check Settings or the Pool tab on your installed firmware. If there is no fallback section or second pool slot, the fallback settings do not apply.
Which DirectPool port should I use as fallback?
Port 3338 to stay solo, with the whole block to you minus 1%, or port 3333 for PPLNS payouts by shares.
Where do I find my Umbrel or Start9 Public Pool address?
In the Public Pool app on your node. It shows the stratum address and port for your local network.
Does the miner switch back to my node automatically?
It depends on the firmware version. The AxeOS dashboard shows which pool is active, and a restart always starts from the primary.
Do I need an account on DirectPool for the fallback?
No. Your Bitcoin address is the username and x is the password.
S

Sources

  1. ESP-Miner (AxeOS) API specification: fallback stratum fieldshttps://github.com/bitaxeorg/ESP-Miner/blob/master/main/http_server/openapi.yaml, checked 2026-11-05
  2. ESP-Miner releaseshttps://github.com/bitaxeorg/ESP-Miner/releases, checked 2026-11-05
  3. Public Pool source codehttps://github.com/benjamin-wilson/public-pool, checked 2026-11-05
  4. Umbrel App Store: Public Poolhttps://apps.umbrel.com/app/public-pool, checked 2026-11-05
  5. Start9: Public Pool for StartOShttps://github.com/Start9Labs/public-pool-startos, checked 2026-11-05

Miners in this guide

Read next