Best pool for your Avalon Nano 3S / Mini 3 heater

By DirectPool. Published . Updated
Short answer

Use a pool that pays straight from the block and needs no account. On DirectPool, put stratum+tcp://stratum.directpool.io:3333 in Pool 1 for PPLNS, or port 3338 for solo, your bc1 or 3 address plus .worker as Worker, and x as Password. Save, reboot, and keep it running in rooms you would heat anyway.

PPLNS port
3333
Solo port
3338
Nano 3S heat
~140 W
Mini 3 heat
~800 W

Which pool should an Avalon heater use?

The Avalon Nano 3S and the Avalon Mini 3 are Canaan miners built to sit in a living room and blow warm air. Both ship pointed at F2Pool through a QR service card, but both accept any standard Stratum pool in their Pool Config page. The pool decides two things: how you get paid, and whether you can check that you were paid.

On DirectPool you pick between two Bitcoin pools on the same server:

  • PPLNS on port 3333. Every block the pool finds pays each miner directly from the block itself, in proportion to their shares over the last 7 days, minus a 1% fee. Balances under 10,000 sats are recorded and paid by a later block.
  • Solo on port 3338. If your heater finds a block, the whole reward goes to your address from the block, minus 1%. If it does not, you get nothing.

There is no account. Your Bitcoin address is the username, so there is nothing to sign up for and no balance held by the pool.

Why does mining make sense as winter heating?

A miner turns almost all the power it draws into heat, exactly like an electric heater of the same wattage. In a room you would heat with electricity anyway, the mining income is a small discount on heat you were going to pay for. Outside heating season the same heat is wasted, or works against your air conditioning.

FigureAvalon Nano 3SAvalon Mini 3
Hashrate (Canaan)about 6 TH/sabout 37.5 TH/s
Power, so heat outputabout 140 Wabout 800 W
Energy per day if left on3.36 kWh19.2 kWh
Noise (Canaan)30 to 40 dB35 to 55 dB depending on mode
Power supply140 W GaN adapterbuilt in, normal wall socket

140 W takes the chill off a small office or bedroom. 800 W is comparable to a small panel heater on a medium setting and can carry a room on its own in mild weather. Canaan rates the Nano 3S for rooms between -5 and 30 degrees Celsius. The daily energy figures are simple arithmetic: watts times 24 hours.

Which settings do you enter on the Nano 3S or Mini 3?

Both models use Canaan firmware, managed with the Avalon Family app (iOS or Android) or the web page at the miner's IP address. Pool settings are under Pool Config, with three pool slots. Avalon uses one combined URL box, so the scheme and port go in the same field.

1. Pool 1 for DirectPool PPLNS

FieldWhat to enter for DirectPool
Pool URLstratum+tcp://stratum.directpool.io:3333
Workerbc1qyouraddress.bedroom
Passwordx
Choose your mining region
Showing Europe, Lithuania (main server).
Changing the location only changes the address shown above. Copy it into your miner settings and restart or reconnect the miner. Miners already connected stay where they are. Every server mines the same pool, with the same payouts.
Browser ping, measured live from this page
Europe, Lithuania...
North America, Chicago...
Asia, Jakarta...
This measures your browser connection, not your miner or the full relay-to-pool path.

2. Or Pool 1 for DirectPool solo

FieldWhat to enter for DirectPool
Pool URLstratum+tcp://stratum.directpool.io:3338
Workerbc1qyouraddress.mini3
Passwordx

Solo on port 3338 always uses the main server address shown here. PPLNS on 3333 can use the closest regional server picked above.

3. Save and reboot

In the app, tap Save; it asks for the miner password (admin on the units we checked) and restarts the miner. In the browser, click Submit, then Reboot from the dashboard. The miner keeps using the old pool until it restarts.

Careful: change the default admin password after setup. Anyone on your network who knows it can point your heater at their own pool.

4. Use Pools 2 and 3 as backups

Pools 2 and 3 are only used when Pool 1 is unreachable. A good pattern is the other DirectPool mode, or another pool you trust, with an address you control. Shares sent to a backup pool are paid on that pool's terms.

5. Pick a work mode for the room

The Avalon Family app lets you choose the work level. Canaan's lowest noise figure for the Nano 3S (30 dB) is measured at the low level, and the Mini 3 noise range depends on the mode. Lower levels mean less heat, less noise and less hashrate. Pick the level for the room, not for the pool: the pool settings do not change.

Solo or PPLNS for a home heater?

The long-run average is the same either way, minus the fee. What changes is how it arrives.

  • PPLNS suits you if you want to see sats arrive over the winter. A 6 TH/s Nano 3S builds up a small balance that is paid once it passes 10,000 sats and the pool finds a block.
  • Solo suits you if you treat the heater as a lottery ticket that also heats the room. The chance of a block is small for one Nano 3S and larger for a Mini 3, but neither is something to plan around.

Your own chance per day and per year at live difficulty is on the odds calculator. The longer comparison is in solo vs pool mining.

How do you check it is mining on DirectPool?

After the reboot the app should show Pool 1 as active and the hashrate rising over a few minutes. Paste your address on the home page for PPLNS or on the Bitcoin solo page for solo. The worker name after the dot appears once the first shares arrive. If the pool shows as dead, the URL is almost always missing stratum+tcp:// or the port; see the connection checklist.

What goes wrong most often?

  1. Scanning the F2Pool card and expecting DirectPool stats. The card sets up F2Pool, not DirectPool.
  2. Typing only stratum.directpool.io. Avalon needs the full URL with scheme and port.
  3. Using an address starting with 1. DirectPool takes bc1 or 3 addresses.
  4. Blocking the vent. The Nano 3S blows warm air out of the top; the Mini 3 needs open space along its length. A blocked vent raises fan noise and can lower hashrate.
  5. Sharing a circuit with a kettle or another heater when running the Mini 3. 800 W around the clock is a large continuous load.

Full device pages: Avalon Nano 3S and Avalon Mini 3. The step by step for the smaller unit is in the Avalon Nano 3S setup guide. Canaan's own pages for the Nano 3S and Mini 3 list the specifications quoted here.

Q

Questions

Can the Avalon Nano 3S and Mini 3 mine on DirectPool?
Yes. Both accept any Stratum pool in Pool Config. Enter stratum+tcp://stratum.directpool.io:3333 for PPLNS or port 3338 for solo, your bc1 or 3 address plus .worker, and x as the password.
Should a home heater mine solo or PPLNS?
PPLNS if you want small payments over the winter, solo if you treat the heater as a lottery ticket. The long-run average is the same minus the fee; only the timing differs.
How much heat does an Avalon miner give?
Almost all of its power: about 140 W for the Nano 3S and about 800 W for the Mini 3, like an electric heater of the same wattage.
Does the work mode change the pool settings?
No. The work level changes heat, noise and hashrate. The Pool URL, Worker and Password stay the same.
What do Pools 2 and 3 do on an Avalon?
They are backups, used only when Pool 1 is unreachable. Shares sent there are paid on that pool's terms.
Why does my Avalon show the pool as dead?
Usually the Pool URL is missing stratum+tcp:// or the port. Avalon needs the full URL in one box. Save and reboot after fixing it.
S

Sources

  1. Canaan: Avalon Nano 3S official page (6 TH/s, 140 W adapter, 30 to 40 dB, -5 to 30 C)https://www.canaan.io/nano3s, checked 2026-11-05
  2. Canaan: Avalon Mini 3 official pagehttps://www.canaan.io/mini3, checked 2026-11-05
  3. Canaan: Avalon Family apphttps://www.canaan.io/avalonfamily/, checked 2026-11-05
  4. DirectPool verify page: fee, payout list and pool ruleshttps://directpool.io/verify/, checked 2026-11-05

Miners in this guide

Read next